(1)波形梁护栏板、立柱、防阻块、横隔梁、端头、螺栓、螺母等构件应符合《高速公路波形梁钢护栏》(JT/T281—1995)及《公路三波形梁钢护栏》(JT/T457—2001)产品标准的规定。生产厂方在提供产品时,应同时提交产品质量合格证书。
(1) waveform beam plate, a vertical column, an anti block, cross beam and an end, bolts, nuts and other components separated should conform to the requirements of the highway guardrail '(JT/T281 - 1995) and the road three wave beam steel guardrail' (JT/T457 -- 2001) standard products of. The manufacturers in providing products, product quality certificate should be submitted at the same time.
(2)波形梁板、立柱、防阻块、端头、托架等部件应符合《碳素结构钢》(GB/T700—1988)的Q235牌号钢的要求。
(2) wave beam plate, column, block, end, bracket and other parts should be in accordance with the 'carbon structural steel' (GB/T700 - 1988) of the Q235 grades of steel requirements.
(3)连接螺栓、螺母、垫圈、横梁垫片等部件应符合《碳素结构钢》(GB/T700—1988)的要求,其抗拉强度不得小于375MPa和400MPa(分别适用于JT/T281—1995和JT/T457—2001)。
(3) connecting bolts, nuts, washers, beam gasket components should comply with the 'carbon structural steel' (GB / T700 - 1988) requirements, the tensile strength shall not be less than 375MPa and 400MPa (were applied to JT/T281 - 1995 and JT/T457, 2001).
(4)高强度拼接螺栓连接副应符合《低合金高强度结构钢》(GB/T1591-1994)、《优质碳素结构钢》(GB/T699-1999)或《合金结构钢》(GB/T3077-1999)的要求,公称直径16mm、8.8S级抗拉荷载不得小于133kN。
(4) high strength bolted splice connection deputy shall comply with the requirements of the low alloy high strength structural steel 'GB/T1591-1994, the high quality carbon structural steel' GB/T699-1999 or the alloy structure steel, GB/T3077-1999, nominal diameter of 16mm, 8.8s tensile load shall not be less than 133kN.
(5)为保证产品质量,对波形梁护栏各部件的外观、尺寸、防腐处理进行抽样检查。不相同的部件各以200件一批为取样单位,单面波形梁护栏,分别取出一片护栏板、一个端头、一根立柱、一块托架进行检查,如果受检的构件不符合要求,另取两件检验;如果这两件中仍有一件不符合要求,则以此为样品的整批产品应被拒收,一切费用由承包人自付。
(6)护栏板、端头梁、立柱的长度和宽度方向不允许焊接,高速波形梁护栏,构件不应出现裂缝。
(7)高强度螺栓应抽样进行楔负载拉力试验,断裂应发生在螺纹部分或螺纹与杆部交接处;如不能做楔负载拉力试验,则应做芯部硬度试验,芯部硬度值为洛氏HRC34~40。螺母应抽样进行保证荷载和硬度试验。
(8)每批高强螺栓都应有出厂合格证,螺栓连接副扭矩应附有扭矩系数的平均值、标准偏差的试验数据和扭矩系数测试时的环境温度等技术资料。